|
A: If you're looking for the sub that will deliver maximum SPL (play loudest), you need to consider sensitivity, enclosure type, and available power. ... Q: How many subwoofers can I hook up to my amplifier? Can I bridge my amp and run two in parallel?
|
www.crutchfield.com/ISEO-rgbtcspd/Learn/learningcenter/...
www.crutchfield.com/ISEO-rgbtcspd/Learn/learningcenter/car/subwoofers_faq.html
|
|
|
|
|
Also, keep in mind that most amplifiers need to see a 4-ohm load when bridged to mono operation. If you want to bridge your amp, you should use one 4-ohm speaker or, if you prefer multiple woofers, wire two 8-ohm speakers in parallel.
|
www.crutchfield.com/ISEO-rgbtcspd/Learn/learningcenter/...
www.crutchfield.com/ISEO-rgbtcspd/Learn/learningcenter/car/amplifiers_glossary.html
|
|
|
the amp can not handle that sub bridged, it is a 2 ohm load if it is a dual 4, you will get either and 2 or 8ohm load for that sub. You need a single 8 or a dual ... Home > Message Board > Car Audio > Amplifiers > Archive through January 06, 2006 > How to bridge 4 ohm sub and amp ... Thread: How to bridge 4 ohm sub and amp...
|
www.ecoustics.com/bbs/messages/4/187611.html
|
|
Date:January 26, 2003 at 13:48:44; From:John Huckins, [207-5-174-92.metrocast.net]; Subject:how to bridge an amp ... i have a Legacy 600 watt amp. im not sure how to bridge it. if u guys could let me know how to bridge it to a pair of DVC subs. id appreciate it. the pattern goes like this; + -; +- +-; thanks alot;
|
www.diysubwoofers.org/talkshop/messages/29131.htm
www.diysubwoofers.org/talkshop/messages/29131.htm
|
|
[Archive] How to wire sub and amp? Stereo & Electronics ... Stereo & Electronics - How to wire sub and amp? ... or you could just go buy a suitable amp/sub for the application and call it a day. your choice; i'd recommend the latter option. having incompatable equipment is about the worst thing you can do.
|
www.ls1tech.com/forums/archive/index.php/t-255430.html
|
|
Stereo & Electronics - Show your Sub/Amp setup ... I already have an Alpine 9815 Head Unit but I still need Speakers, A Sub and an Amp. For the Sub and amp Im going with either a 10W6v2 or a 10W7. Powered with a JL Audio 500/1 amp. For my speakers, I dont know, But most likely I will go with JL Audio ZR. Powered with a JL...
|
www.ls1tech.com/forums/archive/index.php/t-375149.html
|
|
300GB Usb HDD, Griffin pwrmate, m-audio audiophile fw. BU-353 gps. 2x100w sony amps, 1x150w JBL sub amp, MBQuart front components, 6x9 rear, 10" sub. Audiocontrol epcienter, esp2, 3xs. Clifford G5, ... Im running them this way: Channel 1: sub 1, Channel 2 : Sub 2. Is it possible to bridge them and run them at 2 ohms ?
|
www.mp3car.com/vbulletin/car-audio/48591-dual-vioce-coi...
www.mp3car.com/vbulletin/car-audio/48591-dual-vioce-coil-sub-amp-wiring.html
|
|
hi guys, was thinking of building a car sub amp myself. want to know if anyone ... As already indicated by LBM, most common chips can not hold more than 3Amps so theoretically you can not have more than 12v x 3A = 36W leave out few watts as losses, even with bridge mode they are not much efficient (read music to ears).
|
www.team-bhp.com/forum/diy-do-yourself/22403-planning-b...
www.team-bhp.com/forum/diy-do-yourself/22403-planning-build-car-sub-amp-help-needed.html
|
|
I'd use the Punch amp & just turn down the gain so that you don't blow it & you should be fine; OR; Just buy another 10" sub & have 2 subs and then bridge the amp (if needed)....that's what I did!
|
www.redlineforums.com/forums/audio-visual/15003-how-sub...
www.redlineforums.com/forums/audio-visual/15003-how-sub-stereo-amp-install-factory-4.html
|
|
