|
Sometimes your amp will have a diagram for bridging. ... Let's use the 2 channel amp to explain. You should see 4 terminals: a positive (+) and a negative (-) for channel 1; and the same for channel 2. Let's label each terminal, as follows: "A" (channel 1, positive), "B" (channel 1, negative), "C" (channel 2, positive),
|
www.wikihow.com/Bridge-an-Amplifier
www.wikihow.com/Bridge-an-Amplifier
|
|
|
|
Amplifier bridging is simply using 2 channels of an amplifier to drive a common load. For 2 channel amplifiers, one left signal and ... The left channel of the bridgeable amplifier is set up just like the left channel of the non-bridgeable but the right channel of the bridgeable amp is where you will see the difference.
|
www.bcae1.com/bridging.htm
www.bcae1.com/bridging.htm
|
|
|
A 50Wx2 amp bridged would act as a 200Wx1 amp. Unfortunately, you only see about 2/3 to 3/4 of this power. This number is usually the same as the combined power of the 2 channels at half the load. Take the following example of a 2 channel car stereo amplifier: ... Bridging an amp...
|
www.diyaudioandvideo.com/FAQ/Wiring/
|
|
ok as I've said in another post this past weekend i bought a rockford fosgate 2 channel amp its model # p3002 and is rated at 300 watts @ 4 ohms bridged and 75w continuous @ 2x 4ohms and my sub is wirerd for 4 ohms which i believe means its only getting 75w rms? ... You're bridging the amp correct? Do the series wiring...
|
www.explorerforum.com/forums/archive/index.php/t-129922...
www.explorerforum.com/forums/archive/index.php/t-129922.html
|
|
I'm trying to do the same thing in my little egg beater car by running 4 speakers using a 2 channel amp (I have it sitting around, thought I can put it into good use). Although my amp is not a brand name ... On a 2 channel amp that I plan on bridging, do I need BOTH rca ins? FyreDaug Car Audio 67 10-15-2006 09:35 PM...
|
www.mp3car.com/vbulletin/car-audio/100055-2-channel-amp...
www.mp3car.com/vbulletin/car-audio/100055-2-channel-amp-4-speakers-possible-2.html
|
|
Not if it gets tuned right. It would be different if it were a simple deck. Rear fill is minor, its just to get that "behind you sound" that I like better than just a simple component set. 2 components because the mbq's lack low-m...
http://www.mp3car.com/vbulletin/car-audio/87855-2-chann...
|
|
Consumer Electronics Discussions on Home Theater Audio Video including DVD MP3 HDTV and more... ... Home > Message Board > Car Audio > Amplifiers > Archive through January 04, 2005 > Bridging 4 channel amp to 2 subs ... Thread: Bridging 4 channel amp to 2 subs...
|
www.ecoustics.com/bbs/messages/4/115330.html
|
|
you could always try bridging it at 8 ohms, and see how you like it. in theory, it should send the same ... The sub is the IDQ10 D4 V.2, so its the 4 ohm version. Dual 4 ohm voice coils. I was thinking about this more and I want to stay with a 2 channel amp over a mono amp because later on I may decide to go to 2 subs.
|
www.fullsizechevy.com/forums/archive/index.php/t-77714....
www.fullsizechevy.com/forums/archive/index.php/t-77714.html
|
|
Punch 2 Channel Amplifiers ... P250.2 $132.99 ... Punch Stage 2 Subs...
|
www.carstereoworld.com/rockford/rftpunch2amp.html
www.carstereoworld.com/rockford/rftpunch2amp.html
|
|
