Use a miter box or a miter saw. First, some assumptions: A) The moulding used has a 45 degree "spring" or slope. B) the corner you are cutting, inside or outside is 90 degrees. There are 2 ways to do this, depending on whether you...
http://wiki.answers.com/Q/How_do_I_cut_cove_molding
|
|
|
Cove molding is of this type; you will frequently find it stretched around the perimeter of a room where the ceiling joins the wall. Cutting cove molding is a little bit different from cutting most other types of molding, but it is not a difficult task.
|
www.ehow.com/how_4928638_cut-cove-molding.html
www.ehow.com/how_4928638_cut-cove-molding.html
|
|
|
|
|
Cutting a Cove with a Scraper in Woodturning ... Inside cove moulding is one way to hide the spaces and imperfections where the treads and risers of stairs meet. It is that inside corner where the horizontal flat part you step on butts up against the vertical front piece of the stair.
|
www.ehow.com/how_5155246_cut-cove-molding-fit-stairs.ht...
www.ehow.com/how_5155246_cut-cove-molding-fit-stairs.html
|
|
|
need to know how to cut inside and outside corners of cove molding to fit ceilings in two rooms. Thanks Rick Knight. ... In reply to cutting cove molding by Tom Hall on February 27th, 2004 11:36 AM [Go to top of thread] ... how to cut cove moulding by seumas maccombie 9/9/97 06:23 PM (: 2, : 9)
|
www.bobvila.com/wwwboard/messages/244129.html
|
|
I am trying to cut cove moulding for a room with a cathedral ceiling. Therefore some of the angles are more than 90 degrees between the wall and the ceiling and some of them are less than 90 degrees. I am using a chopsaw and was wondering if you could give ... cutting cove moulding by Brett Hart 2/25/04 09:39 AM (: 1, : 0)
|
www.bobvila.com/wwwboard/messages/45854.html
|
|
I am not sure that you need to cope cove molding for inside corners. I think a butt joint with the compound miter cut to account for the angle of the cove (45 degrees) and the corner will work correctly. Practice this cut with some scrap to make sure you are cutting it right...
|
www.handymanusa.com/questions/trimmoldingq.html
www.handymanusa.com/questions/trimmoldingq.html
|
|
This is the method I used for making the cove moulding on the FirePlace Surround. I used the instructions from WOOD Magazine to set this up. Plan on makin extra, just in case you screw-up! I made two 7' assemblies for the mouldings.
|
www.binkyswoodworking.com/CoveMouldingTip.htm
www.binkyswoodworking.com/CoveMouldingTip.htm
|
|
Cove Moulding - 2 Flutes Cove Moulding - 1" BORE ... Cutter Cutting Overall ... Cove Moulding 1" BORE...
|
www.cutterbits.com/cove-moulding.html
www.cutterbits.com/cove-moulding.html
|
|
Elite Crown Moldings offers many standard Cornice mouldings commonly refered to as cove moulding or crown mouldings has graced cottages and castles alike for centuries. It is uncommon in modern homes mainly because of cost, difficulty of installation and the time it takes to install. ... About US Contact us...
|
trims.elitecrownmoldings.com/
trims.elitecrownmoldings.com/
|
|
