There should be a sticker on the fan shroud telling you which wire to disconnect. On the older tbi motors it was tan with a black stripe i believe. Disconnect this wire, the loosen the dist. bolt and check the timing with a timing gun. Rota...
http://wiki.answers.com/Q/How_do_you_time_a_350_Vortec_...
|
|
|
In responce to 350 question.I always set time to top dead center with rotary button on #1 plug wire and advance time 4 to 6 degrees to get motor started. Once motor starts,I set time where motor will idle smoothly. ... How To Guide...
|
forums.carcraft.com/70/6781624/street-car-tech/chevy-35...
forums.carcraft.com/70/6781624/street-car-tech/chevy-350-with-edelbrock-top-end-upgrade-timing-ad/index.html
|
|
|
|
Timing dynamically is fairly simple and is the best way to time your engine. Static timing is good for ... The first step to setting your timing is to adjust your valves. Valve adjusting is to be done on a stone cold engine and is a topic for another procedure, but John Muir explains well how to do it in his Idiot book.
|
www.type2.com/bartnik/timing.htm
www.type2.com/bartnik/timing.htm
|
|
|
The engine is a 1974 Chevy 350, Flat top pistons 10:1, 224/224 cam, had the heads done new valves, guides, seats and springs. Mallory Magnetic breaker less distributor. Holley 600 CFM carb and a Dual plane RPM performer manifold. ... 14 degrees at the crank sounds good to me. I have a cam a little bigger than your's and it...
|
www.hotrodders.com/forum/timing-specs-chevy-350-engine-...
www.hotrodders.com/forum/timing-specs-chevy-350-engine-4756.html
|
|
The motor runs better. My next move is try "manual timing". Here's how a friend explained how you do that: 1.) retard until it runs rough at idle, 2.) advance to where it smooths out, 3.) run to 160F - 180F and listen for pre-ignition ... El Camino Engine - 350 Chevy or 455 Pontiac bjam2 Engine 16 08-07-2007 03:45 PM...
|
www.hotrodders.com/forum/chevy-350-timing-79507.html
www.hotrodders.com/forum/chevy-350-timing-79507.html
|
|
The first thing you'll need to do to set your timing is to check your owner's or shop manual for the correct settings for your car (also see spec plate under hood). ... This may get frustrating the first time you do it. But it's well worth the effort when you consider the cost of having a shop do the work for you.
|
www.hotrodder.com/kwkride/timing.html
www.hotrodder.com/kwkride/timing.html
|
|
I have a 1990 chevy 350 engine strapped to a chevy 1990 chevy c/k 3500 2wheel drive single rear wheel truck. I pull my horse trailer(not fifth wheel) and i would like to get more power out of my 350 engine to make pulling on the hills easier. ... All times are GMT -5. The time now is 08:35 AM.
|
www.truckforums.com/m_820/tm.htm
|
|
Oct 3, 2008 ... if i put #1 on tdc, line up rotor with #1 wire engine backfires thru ... You did not say what year you have. Hear is the deal Distributor tooth ...
|
answers.yahoo.com/question/index?qid=20081003191534AAPJ...
answers.yahoo.com/question/index?qid=20081003191534AAPJwh8
|
|
I would take out the no# 1 plug and take off the coil wire, now have some one tap the kep and keep tapping it with your finger covering the plug hole, soon it will blow off, stop turning it at that time, now with the dist. ... ; You are here: Experts > Shopping > Cars > Chevrolet > 350 chevy;
|
en.allexperts.com/q/Chevrolet-775/350-chevy-1.htm
en.allexperts.com/q/Chevrolet-775/350-chevy-1.htm
|
|
