|
Truss Frame Construction, Truss Glossary Definition of Terms ... FlREPLACE TRUSS A Truss fabricated with a modified shape to allow clearance for the penetration of a chimney through the roof, whose loads are supported by a master (girder) Truss. (requires special engineering)
|
www.truss-frame.com/truss-glossary.html
www.truss-frame.com/truss-glossary.html
|
|
|
|
Wheeler: Supplier of wood roof and floor truss systems and wholesale building products. ; ... A structural support, usually a beam or a wall that is designed by the building designer to carry the truss reaction loads to the foundation. ... A conventionally framed wood girder located between stud, joist, or truss opening.
|
www.wheeler-con.com/truss/pages/genltrus.html
www.wheeler-con.com/truss/pages/genltrus.html
|
|
|
|
Apex/Peak: The uppermost point of a truss. ... Bearing: A structural support, usually a wall that occurs at the top or bottom chord or between the end points of a roof or floor truss. ... Girder Truss: Usually a multiple-ply truss designed to carry other trusses over an opening.
|
www.razortruss.com/trussterms.htm
www.razortruss.com/trussterms.htm
|
|
|
“ |
now THAT is a girder truss ! In beautiful douglas fir timbers with steel joinery. Handcrafted and installed by us, Vermont Timber Works Before the raising ...at the Centennial Senior Center in Concord, NH. Ok, where's the crane and our cr...
http://great-room-timber-truss.blogspot.com/2008/01/wha...
|
|
• GTWS2T shall be installed to a minimum 2x4 vertical member of a girder truss with no restriction on the size of the bottom chord. • GTWS3T shall be installed to a minimum 2x6 vertical member of a girder truss with no restriction on the size of the bottom chord.
|
www.uspconnectors.com/gtws.shtml
|
|
girder truss, load bearing wall, roof truss: Terry, The details you provided in your follow-up don t put me at ease about the structural adequacy of your contractor s design. Depending on the span of your existing (site-built, you mentioned) trusses, and a couple of other factors, the load on...
|
en.allexperts.com/q/Building-Homes-Extensions-2333/Addi...
en.allexperts.com/q/Building-Homes-Extensions-2333/Addition-8.htm
|
|
girder truss, load bearing wall, roof truss: Terry, It depend on the size of your new truss, and its supporting columns in the new or existing walls. This is called a girder truss, and in your case, depending on the span, should probably be at least a two-ply member (so 3 or more wide). ... Expert: Ted Barnhill (Principal,
|
en.allexperts.com/q/Building-Homes-Extensions-2333/Addi...
en.allexperts.com/q/Building-Homes-Extensions-2333/Addition-7.htm
|
|
I am working on the preliminary design of a fabricated steel girder truss (Pratt) for a roof application. The truss depth is limited to 9' by architectural constraints (unless I can show that it will not work). I have modeled the truss geometry in STAAD to size the members and to determine deflections.
|
www.eng-tips.com/gviewthread.cfm/lev2/21/lev3/68/pid/50...
www.eng-tips.com/gviewthread.cfm/lev2/21/lev3/68/pid/507/qid/48864
|
|
“ |
A girder bridge is one in which a girder (huge i-beam roughly) is placed along side the roadway which is supported between the flanges of the beam. A trussed Girder bridge constructs the beam out of smaller elements arranged in triangles - ...
http://uk.answers.yahoo.com/question/index?qid=20080709...
|
|
